Home / Services / Page

Culvert Crossings in Kansas City

We build culvert crossings for driveways, private roads and site access over ditches and creeks across the Kansas City metro. One crew sets the pipe, builds the ends and rebuilds the drive over it.

Since 2015

GPS machine control

Licensed and insured

Since 2015

Licensed and insured

GPS machine control

Excavator removing a backyard pool at a Kansas City area home

Culvert Crossing Services We Provide

Driveway Crossings Over Ditches and Creeks

New pipe and fill under the drive where it meets a ditch or creek, with land grading on either side when water needs steering to the pipe.

Private Road and Access Crossings

Access crossings tied to private roads and shared drives, built in step with our gravel driveway and private road work.

Temporary and Permanent Roadway Crossings

Temporary crossings for site access during development and permanent crossings under new roads, set before roadway prep and base work.

Field Crossings on Rural Land

Field crossings on acreage and farm ground in CMP, RCP or HDPE pipe, so trucks and equipment reach the far side of a ditch.

Rebuilding Failed or Washed-Out Crossings

Crushed, collapsed or undersized pipe pulled and replaced, with new bedding, fill and surface. We check whether the old pipe was undersized or installed wrong before the new one goes in.

Headwalls, End Sections and Riprap

Headwalls, end sections and flared ends at the inlet and outlet, with riprap to keep the banks and channel from scouring.

What Your Quote Covers

Pipe: CMP, RCP or HDPE in the size and material your engineer, permit or road owner specifies.

Bedding and backfill: placed in 6-inch lifts and compacted to 95% of standard Proctor.

Inlet and outlet shaping: the ditch or channel graded into and out of the pipe.

Ends and armor: headwalls, end sections or flared ends, plus riprap.

Drive surface: base and rock rebuilt over the pipe to match the drive or road.

What’s not included

pipe sizing design

permit fees

bridges or box culverts

Kansas City Site Conditions We Plan For

Wet clay backfill: metro clay placed wet settles over the pipe and leaves a dip in the drive. We place it in lifts near optimum moisture.

Fast storm runoff: clay sheds water quickly, and an unarmored outlet scours out. We quote ends and riprap with the crossing.

Shale on creek slopes: soils on slopes down to creeks can sit on shale, so a crossing cut may hit rock. We adjust trench depth and bedding where it shows up.

How the Job Runs

01

Site walk and quote:

we look at the ditch or creek, the drive and equipment access, then quote the crossing.

02

Confirm size and permits:

pipe size and any permits come from your engineer, the county or the road owner before we dig.

03

Dig and bed to grade:

GPS machine control holds trench grade and the pipe's flow line from inlet to outlet.

04

Set pipe and backfill:

pipe goes in on prepared bedding, then backfill in compacted lifts.

05

Build ends and armor:

headwalls or end sections and riprap at both ends.

06

Handoff:

a drivable crossing with a protected outlet and the surface rebuilt over the pipe.

Send us the site and any plan or permit you have, and we'll quote the crossing.

Where We Work

We build culvert crossings from Grain Valley across the Kansas City metro, including rural drives and acreage around Oak Grove, Concordia, Liberty and Odessa.

Culvert Crossing FAQs

Do I need a permit for a creek crossing?

Often, and it can come from more than one agency. A crossing in a road ditch follows the road owner's permit (MoDOT, the county or the city), and work in a creek can need a U.S. Army Corps of Engineers permit, often a nationwide permit. Check with the Corps Kansas City District before work starts; we build to the permit you get.

Who decides the pipe size?

Your engineer, the county or the road owner. In unincorporated Clay County, the county inspects the site and lists the required culvert size on the driveway permit (as of November 2026; confirm with your permitting office). We set the pipe the plan or permit calls for.

What drives the cost of a crossing?

Pipe size, length and material, the depth of the ditch or channel, the ends and riprap, and how much drive surface gets rebuilt. Equipment access and whether old pipe has to come out also move the number, so we quote after a site walk.

Can you replace a crossing that keeps washing out?

Yes. We pull the failed pipe, rebed the new one, backfill in compacted lifts and armor both ends, the same culvert replacement work we do under roads and drives. When washouts suggest the old pipe lacked capacity, your engineer or road owner sets the new size.

What do you need from me before we start?

Site access, any plan or permit for the crossing, and the pipe size if your engineer or road owner has set one. If the crossing sits on a public road or in a creek, have that permit in hand before we schedule.

Get a Quote for Culvert Crossings

Tell us what you need to cross and what will drive over it, and we'll quote the crossing. Call ICON at (816) 867-5134 or request a quote at icongrading.com.